查看完整版本 : 0W16偈油

lso8 2018-7-3 10:08 AM

0W16偈油

有無人知除咗新款serana, 重有咩車指定要用0W16偈油

lso8 2018-7-5 10:17 AM

咁即係得一款車用佢,唔使指意街外有得賣,死局要返大昌換偈油!

chuenwai 2018-7-5 10:39 AM

可以入零件部買走:smile_44:

30100142 2018-7-5 12:00 PM

0-16,很特別。
如果轉 0-30 就好容易搵到

plm8051 2018-7-5 12:04 PM

[quote]原帖由 [i]lso8[/i] 於 2018-7-3 10:08 AM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483088038&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]
有無人知除咗新款serana, 重有咩車指定要用0W16偈油 [/quote]
你有冇睇清楚manual?通常都會有一個範圍,唔同氣溫都唔同範圍,點會指定一款?

skikk2 2018-7-5 02:32 PM

[quote]原帖由 [i]lso8[/i] 於 2018-7-3 10:08 AM 發表 
有無人知除咗新款serana, 重有咩車指定要用0W16偈油 [/quote]


喺日本見過…
樓主可以問吓王官零件部有無?
[attach]8489195[/attach]

skikk2 2018-7-5 08:11 PM

日系新車要求0W嘅偈油度數,適合 -30C 至 40C,有啲欧系新車款直情唔提ambient temperature…
[attach]8490303[/attach]

skikk2 2018-7-5 08:21 PM

0W16,0W20,0W30,0W40,W後面嘅16,20,30,40係指引擎運作温度(若100C)嘅偈油度數要求,同環境温度(ambient temperature)無関…

NorrisHKman 2018-7-5 08:32 PM

[quote]原帖由 [i]plm8051[/i] 於 2018-7-5 12:04 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483212564&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]

你有冇睇清楚manual?通常都會有一個範圍,唔同氣溫都唔同範圍,點會指定一款? [/quote]

十幾年前嘅車已可用一種viscosity通行全球啦

NorrisHKman 2018-7-5 08:39 PM

[quote]原帖由 [i]skikk2[/i] 於 2018-7-5 08:21 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483238223&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]
0W16,0W20,0W30,0W40,W後面嘅16,20,30,40係指引擎運作温度(若100C)嘅偈油度數要求,同環境温度(ambient temperature)無関… [/quote]

0w16中嘅 "16",與0w20中嘅 "20"係,完全不同嘅比較 "方式"

有如C200中嘅"200",與C63中嘅"63",可以比較咩?



The number 16 itself does not have a special meaning it does not point at any specific oil property, it is only the name of the viscosity grade. SAE decided to choose a number that breaks the must-be-divisible-by-5 rule to avoid any mix-up with the winter viscosities. SAE 15 would have been easy to confuse with 15W (even though the very same problem did not influence SAE's decision when SAE 20 was introduced).

With the introduction of SAE 16 the limit on 100 °C viscosity for SAE was changed from 5.6 cSt to 6.9 cSt minimum. SAE 20 oils didn't make use of this interval so far and the limits for SAE 16 partially extend to this segment. For an oil to be of SAE 16 viscosity grade its viscosity on 100 °C must be between 6.1 and 8.2 mm2/s and its HTHS viscosity must be at least 2.3 mPa*s.

plm8051 2018-7-5 09:30 PM

[quote]原帖由 [i]skikk2[/i] 於 2018-7-5 08:11 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483237783&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]
日系新車要求0W嘅偈油度數,適合 -30C 至 40C,有啲欧系新車款直情唔提ambient temperature…
8490303 [/quote]

頂,係唔係honda只出1款偈油?為咗推銷呢款偈油就所有偈油資訊都唔出,等你冇得諗,用其他廠就話之你。

skikk2 2018-7-5 09:32 PM

[quote]原帖由 [i]NorrisHKman[/i] 於 2018-7-5 08:39 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483239057&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]


0w16中嘅 "16",與0w20中嘅 "20"係,完全不同嘅比較 "方式"

有如C200中嘅"200",與C63中嘅"63",可以比較咩?



The number 16 itself does not have a special meaning it does not point at any specific oil property, it is only the ... [/quote]


I'm saying the numbers after W, namely, 16, 20, 30, 40, etc. are refering to the oil viscosity requirements at engine operating temperature and therefore has no relevancy to the ambient temperature.

Btw I understand what you mean about the new standard for lower viscosity oils.  In fact it is interesting to note the evolution of the standard of oil viscosity because the trend is heading towards lower viscosity.

plm8051 2018-7-5 10:28 PM

[quote]原帖由 [i]NorrisHKman[/i] 於 2018-7-5 08:32 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483238731&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]


十幾年前嘅車已可用一種viscosity通行全球啦 [/quote]

一種通行同只限一種係兩回事,咁如果冇0w16可唔可以用其它黏度先?

NorrisHKman 2018-7-5 11:14 PM

[quote]原帖由 [i]plm8051[/i] 於 2018-7-5 10:28 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483245301&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]


一種通行同只限一種係兩回事,咁如果冇0w16可唔可以用其它黏度先? [/quote]

你明唔明當中嘅 "16" 係乜?

plm8051 2018-7-5 11:28 PM

[quote]原帖由 [i]NorrisHKman[/i] 於 2018-7-5 11:14 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483247660&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]


你明唔明當中嘅 "16" 係乜? [/quote]
油溫於攝氏100度之下的黏度.

NorrisHKman 2018-7-5 11:33 PM

[quote]原帖由 [i]plm8051[/i] 於 2018-7-5 11:28 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483248267&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]

油溫於攝氏100度之下的黏度. [/quote]

攝氏100度時
0w16 vs 0w20, 邊隻稀d?

plm8051 2018-7-5 11:34 PM

[quote]原帖由 [i]NorrisHKman[/i] 於 2018-7-5 11:33 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483248484&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]


攝氏100度時
0w16 vs 0w20, 邊隻稀d? [/quote]
0w16 稀d

NorrisHKman 2018-7-5 11:38 PM

[quote]原帖由 [i]plm8051[/i] 於 2018-7-5 11:34 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483248571&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]

0w16 稀d [/quote]

Really?

plm8051 2018-7-5 11:56 PM

[quote]原帖由 [i]NorrisHKman[/i] 於 2018-7-5 11:38 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483248722&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]


Really? [/quote]
[url]https://passenger.lubrizoladditives360.com/low-viscosity-sae-16-oils-will-require-cutting-edge-additive-technology-to-address-wear-challenges/[/url]
In addition to the introduction of SAE 16 last April, the new revision to J300 also included a change in the minimum high-temperature viscosity range of SAE 20. With a previously set KV minimum limit measured at 100°C of 5.6 mm2/s, the lower portion of the SAE 20 range was not being utilized by OEMs. [color=#0000ff]As a result, the limit was raised to 6.9 mm2/s[/color], which effectively narrowed SAE 20’s range and made it similar to that of higher-viscosity grades.

plm8051 2018-7-5 11:59 PM

[quote]原帖由 [i]NorrisHKman[/i] 於 2018-7-5 11:38 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483248722&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]


Really? [/quote]
1[attach]8491454[/attach]

NorrisHKman 2018-7-6 12:47 AM

[quote]原帖由 [i]plm8051[/i] 於 2018-7-5 11:59 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483249611&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]

18491454 [/quote]

我用SAE J300 standard

plm8051 2018-7-6 08:54 AM

[quote]原帖由 [i]NorrisHKman[/i] 於 2018-7-6 12:47 AM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483251258&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]


我用SAE J300 standard [/quote]
下面呢張係2015年 SAE J300, 你嗰張係邊一年?
[attach]8492207[/attach]

NorrisHKman 2018-7-6 09:24 AM

[quote]原帖由 [i]plm8051[/i] 於 2018-7-6 08:54 AM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483257716&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]

下面呢張係2015年 SAE J300, 你嗰張係邊一年?
8492207 [/quote]

原木2015年revise咗,格硬推高咗20裝就16同8

lso8 2018-7-9 02:26 PM

[quote]原帖由 [i]plm8051[/i] 於 2018-7-5 12:04 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483212564&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]

你有冇睇清楚manual?通常都會有一個範圍,唔同氣溫都唔同範圍,點會指定一款? [/quote]
我架係日產, Manual 指明0W16, 如沒有可用0W20。如果每次換偈油都要返大昌,咁就無命矣!

plm8051 2018-7-9 04:03 PM

[quote]原帖由 [i]lso8[/i] 於 2018-7-9 02:26 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483448740&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]

我架係日產, Manual 指明0W16, 如沒有可用0W20。如果每次換偈油都要返大昌,咁就無命矣! [/quote]
上網搜尋過, 原來依家有啲新引擎係專登設計用0W16, 目的為咗慳油, 你如果唔用0W16, 係可以用高啲的偈油例如0W30 5W30,  愈高SAE愈杰, 對引擎保護性愈強, 但代價係食油咗, 同埋天冷開車時候比較杰可能傷偈, 不過香港天氣唔會低過0度, 只要你買5W或以下就冇問題.
如果你唔介意食油, 係可以用高啲SAE偈油.

skikk2 2018-7-10 05:34 PM

[quote]原帖由 [i]lso8[/i] 於 2018-7-9 02:26 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483448740&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]

我架係日產, Manual 指明0W16, 如沒有可用0W20。如果每次換偈油都要返大昌,咁就無命矣! [/quote]


0W-20 喺香港唔難買到…

skikk2 2018-7-10 05:44 PM

喺日本普通一架租車都係用0W-16

[attach]8510883[/attach]

lso8 2018-7-11 01:07 PM

[quote]原帖由 [i]skikk2[/i] 於 2018-7-10 05:34 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483512061&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]



0W-20 喺香港唔難買到… [/quote]
响上水粉嶺北角都揾唔到,可否明示

subming 2018-7-11 02:38 PM

[quote]原帖由 [i]lso8[/i] 於 11/7/2018 13:07 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483557821&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]

响上水粉嶺北角都揾唔到,可否明示 [/quote]
我經錦田元朗一帶唔會無、除非你指定要某隻牌子

skikk2 2018-7-12 11:35 AM

[quote]原帖由 [i]lso8[/i] 於 2018-7-11 01:07 PM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=483557821&ptid=27552414][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]

响上水粉嶺北角都揾唔到,可否明示 [/quote]


揾到T記衣隻0W20未?[attach]8517982[/attach]
頁: [1] 2
查看完整版本: 0W16偈油