查看完整版本 : 寶馬323i維修問題

gogoswim 2018-8-14 09:06 AM

寶馬323i維修問題

琴日小弟部2011年323I 用車發覺車好震,同轉數錶跳黎跳去,好唔穩定,開車後發覺力水差左好多,同埋發覺引擎故障燈著左,停車開車一踏迫力就好震,因為已經行駛中,冇辦法停車,後來楂左5分鐘又發覺引擎故障燈熄左,行車又順番,咁就照楂去車房,當到達,車房師傳著車時就著唔到,師傳話係引擎入面螺絲斷咗,2個蝴蝶返掩到期,其他野要左檢查,想問下其實我架車依類問題,嚴唔嚴重,要整幾錢度?

ac_schnitzer 2018-8-14 09:45 AM

就咁就 check 到, 師傅有x Ray 眼?? 唔插機睇有乜fault code ?

gogoswim 2018-8-14 09:49 AM

[quote]原帖由 [i]ac_schnitzer[/i] 於 2018-8-14 09:45 AM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=485536045&ptid=27642362][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]
就咁就 check 到, 師傅有x Ray 眼?? 唔插機睇有乜fault code ? [/quote]
琴晚6點先去到車房,咁佢初步咁睇就係,要到今日佢地返工幫我詳細檢查先可以確實

ac_schnitzer 2018-8-14 09:53 AM

反而我初步估係火咀或點火coil問題

mugqq 2018-8-14 09:54 AM

車房師傅咁勁, 撻唔到車就知道引擎入面有螺絲斷咗? :smile_42:

gogoswim 2018-8-14 09:57 AM

[quote]原帖由 [i]mugqq[/i] 於 2018-8-14 09:54 AM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=485536628&ptid=27642362][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]
車房師傅咁勁, 撻唔到車就知道引擎入面有螺絲斷咗? :smile_42: [/quote]
Sorry 我講唔清楚,後尾著車俾油俾冇動力,同埋引擎折開偈油蓋有個位係會轉,佢轉唔到,所以話螺絲斷咗,但都係初步睇,今日佢先幫我深入檢查

mugqq 2018-8-14 10:06 AM

[quote]原帖由 [i]gogoswim[/i] 於 2018-8-14 09:57 AM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=485536842&ptid=27642362][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]

Sorry 我講唔清楚,後尾著車俾油俾冇動力,同埋引擎折開偈油蓋有個位係會轉,佢轉唔到,所以話螺絲斷咗,但都係初步睇,今日佢先幫我深入檢查 [/quote]有無親眼睇住佢拆嘩佬蓋, 睇到邊個位應該轉但轉唔到?

gogoswim 2018-8-14 10:18 AM

[quote]原帖由 [i]mugqq[/i] 於 2018-8-14 10:06 AM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=485537432&ptid=27642362][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]
有無親眼睇住佢拆嘩佬蓋, 睇到邊個位應該轉但轉唔到? [/quote]

[attach]8652687[/attach]相中紅圈位置,我只係見師傅開左依個蓋用燈照,話我知俾油時依組野冇變動,咁係螺絲斷咗,要左詳細檢查先知道(圖中唔係本人車,同埋用圖表達清晰d)

mugqq 2018-8-14 10:27 AM

[quote]原帖由 [i]gogoswim[/i] 於 2018-8-14 10:18 AM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=485538129&ptid=27642362][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]


8652687相中紅圈位置,我只係見師傅開左依個蓋用燈照,話我知俾油時依組野冇變動,咁係螺絲斷咗,要左詳細檢查先知道(圖中唔係本人車,同埋用圖表達清晰d) ... [/quote]都撻唔著車, 裡面全部機件都唔會郁架啦, 想整好架車又唔會比人劏, 贈你3個字..........................換 車 房

3個含情的甩頭 2018-8-14 10:48 AM

[quote]原帖由 [i]mugqq[/i] 於 2018-8-14 10:27 AM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=485538662&ptid=27642362][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]
都撻唔著車, 裡面全部機件都唔會郁架啦, 想整好架車又唔會比人劏, 贈你3個字..........................換 車 房 [/quote]


同意,換車房。

astinaringo 2018-8-14 11:34 AM

叫車房唔好玩啦,引擎組件邊有咁易斷,除非斷 cam帶,但斷 cam帶你又揸唔到去車房啦,快D攞番部車,唔係就唔止斷螺絲咁簡單

salondelouis 2018-8-14 11:35 AM

油汞fuse,油汞到期.

subming 2018-8-14 11:44 AM

引擎入面螺絲斷咗、唔知會係邊一支呢:lol

yeukfung 2018-8-14 11:53 AM

[quote]原帖由 [i]gogoswim[/i] 於 2018-8-14 09:06 AM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=485534006&ptid=27642362][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]
琴日小弟部2011年323I 用車發覺車好震,同轉數錶跳黎跳去,好唔穩定,開車後發覺力水差左好多,同埋發覺引擎故障燈著左,停車開車一踏迫力就好震,因為已經行駛中,冇辦法停車,後來楂左5分鐘又發覺引擎故障燈熄左,行車又順番,咁就照楂去車房,當到達,車房師傳著車時就著唔到,師傳話係引擎入面螺絲斷咗,2個蝴蝶返掩到期,其他野要左檢查,想問下其實我架車依類問題,嚴唔嚴重,要整幾錢度? ... [/quote]

[attach]8652946[/attach]

with your car, i assume your car is N52N engine, which is newer version of N52...

For your case, I have same situation as yours before, while finally identified is one of the ignition coil goes wrong...

it start driving very rough and engine light turns on after 1 minutes of roughness... and i keep slight throttle over few minutes, and it suddenly become smooth again. and engine light turns off, but the power isn't real good.

when attaching to BMW computer, you should find a cylinder misfire code stored in DME.

For my real case, i found that one of the ignition boot is cracked and causing misfire, there are so many reasons having misfire, my case is just for your reference. (i saw some is valve cover seal leakage, got so much oil stucked inside the sparkplug coil hole causing misfire, etc)

Regarding the oil cap in our N52 engine, we need to push down the surrounding cover in order to turn it over, just give a little power and it should turn, that part is simply a cover does not have any screws inside...

Regarding the throttle body, please avoid changing, as throttling logic in N52 is mainly controlled by valvetronic (VVT) motor, instead of the throttle body(only used as fallback if VVT motor goes aways), so if c-fu asking you to change entire throttle body, that's non-sense.. and probably he don't know much in N52 engine.

As other c-hing suggested, just change a trustable 車房.

yeukfung 2018-8-14 11:56 AM

[quote]原帖由 [i]salondelouis[/i] 於 2018-8-14 11:35 AM 發表 [url=https://www.discuss.com.hk/redirect.php?goto=findpost&pid=485542783&ptid=27642362][img]https://www.discuss.com.hk/images/common/back.gif[/img][/url]
油汞fuse,油汞到期. [/quote]

agree, that could be the possible reason too

gogoswim 2018-8-14 12:05 PM

唔該曬咁多位呀🙏🙏🙏🙏

gogoswim 2018-8-14 12:34 PM

唔該曬咁多位師兄意見,麻煩曬

mobilesss 2018-8-14 01:55 PM

正品宝馬

吸不透的香煙 2018-8-14 02:02 PM

換車房啦。
電腦都唔插就知壞乜。
9成自己冇腦,要問人借,但又夜媽媽
頁: [1]
查看完整版本: 寶馬323i維修問題